Motion Reliability of Industrial Robots

I study the motion reliability of industrial robot systems because reliability is the foundation that allows an industrial robot to perform precise, repeatable, and safe operations over a full task cycle. An industrial robot is widely used in welding, drilling, engraving, assembly, palletizing, spraying, and medical manipulation, and in all of these applications the end effector must follow a desired trajectory while many uncertain factors act on the mechanical body. Manufacturing tolerances, assembly errors, joint clearance, link deformation, gear transmission error, friction, wear, and vibration introduce deviations between the commanded pose and the actual pose. I therefore treat motion reliability as a probabilistic measure that quantifies how likely an industrial robot is to remain inside a specified tolerance zone during a specific task.

In my review, I separate motion reliability into point reliability and time-varying reliability. Point reliability describes the probability that the end effector of an industrial robot lies within an allowable error region at a single instant or at a small number of critical points. Time-varying reliability describes the probability that every point along a continuous trajectory remains within the allowable region during an entire interval. This distinction is important because an industrial robot may be highly reliable at one inspection point yet fail elsewhere along a continuous path. I systematically construct kinematic and error models, formulate reliability models, compare solution methods, and propose future research directions for industrial robot motion reliability.

Reliability Concepts for Industrial Robots

Reliability in an industrial robot is not a single scalar property. It depends on the task, the tolerance threshold, the duration, the payload, the controller, and the uncertain parameters of the mechanical structure. I define motion reliability as the probability that the actual motion of an industrial robot satisfies a set of performance constraints. When the constraint is evaluated at one pose, the result is point reliability. When the constraint is evaluated over a continuous time interval, the result is time-varying reliability. I use this classification because it clarifies the mathematical formulation and the numerical method that should be selected.

Reliability type Evaluation domain Typical industrial robot tasks Main limitation
Point reliability A single pose or a discrete set of poses Point welding, drilling, rapid positioning, pick-and-place Neglects failure risk at other points along the path
Time-varying reliability A continuous task interval Welding, spraying, medical surgery, contour tracking Higher computational cost and more complex modeling

For an industrial robot, point reliability is often used when the operation is defined by a sequence of target points. The end effector must reach each point with a position and orientation error below a threshold. If the error vector lies inside a tolerance sphere or a tolerance region, the point is considered reliable. If the error exceeds the boundary, the point is considered failed. This definition is intuitive and computationally convenient, but I must emphasize that it does not guarantee that the trajectory between two points is valid.

Time-varying reliability is more appropriate when the industrial robot must follow a continuous path. In welding or spraying, for example, the tool center point must stay within a narrow tolerance band during the whole motion. A single excursion outside the band can produce a defective weld or an uneven coating. I therefore define time-varying reliability as the probability that the maximum deviation over the entire interval does not exceed the allowable error. This definition transforms the problem into an extreme-value problem or a first-passage problem.

Kinematic and Error Modeling

To evaluate the motion reliability of an industrial robot, I first construct a kinematic model that maps joint variables to the pose of the end effector. The Denavit-Hartenberg method is a classical approach. I assign a coordinate frame to each link and use four parameters: link length, link twist, link offset, and joint angle. The transformation between adjacent frames is expressed as a homogeneous matrix. For an industrial robot with revolute joints, the joint angle is the variable, while the other parameters are constant or uncertain.

$$ T_i^{i-1} = \begin{bmatrix} \cos\theta_i & -\sin\theta_i\cos\alpha_i & \sin\theta_i\sin\alpha_i & a_i\cos\theta_i \\ \sin\theta_i & \cos\theta_i\cos\alpha_i & -\cos\theta_i\sin\alpha_i & a_i\sin\theta_i \\ 0 & \sin\alpha_i & \cos\alpha_i & d_i \\ 0 & 0 & 0 & 1 \end{bmatrix} $$

I then obtain the pose of the end effector relative to the base frame by multiplying the link transformations:

$$ T_n^0 = \prod_{i=1}^{n} T_i^{i-1} $$

An improved version of the Denavit-Hartenberg convention places each joint frame at the proximal end of the link. This modification makes the relationship between frames and joints clearer and reduces the complexity of model construction for an industrial robot with many degrees of freedom. I use either convention depending on the structure of the industrial robot and the required clarity of the error model.

The error model describes how deviations in geometric parameters and joint variables propagate to the end effector. Let the nominal joint vector be $\mathbf{q}$ and the nominal geometric parameter vector be $\mathbf{p}$. The actual pose is a function of the actual joint variables and actual link parameters. I linearize the pose error around the nominal configuration and obtain:

$$ \Delta \mathbf{X} = \mathbf{J}_q(\mathbf{q}, \mathbf{p}) \Delta \mathbf{q} + \mathbf{J}_p(\mathbf{q}, \mathbf{p}) \Delta \mathbf{p} $$

Here, $\Delta \mathbf{X}$ is the pose error vector of the end effector, $\mathbf{J}_q$ is the Jacobian with respect to joint variables, $\mathbf{J}_p$ is the Jacobian with respect to link parameters, and $\Delta \mathbf{q}$ and $\Delta \mathbf{p}$ are the corresponding variations. For an industrial robot, the geometric parameter errors are often dominant because the working environment is relatively stable and the controller compensates for some dynamic effects. However, joint clearance, gear backlash, and link flexibility can also be significant, especially at high speed or under heavy payload.

Error source Physical origin Effect on industrial robot motion Typical modeling approach
Link length error Manufacturing tolerance Position error at the end effector Additive variation in D-H parameters
Link twist error Assembly misalignment Orientation error and position error Additive variation in D-H parameters
Joint angle error Encoder resolution, control error Pose error along the motion Random variable in joint space
Joint clearance Wear, fit tolerance, impact Nonlinear deviation, impact-induced vibration Additional degree of freedom or equivalent linkage
Gear transmission error Backlash, tooth profile error Periodic or stochastic joint error Transmission error model
Link deformation Elastic bending, thermal expansion Time-varying pose error Finite element or compliance model
Vibration Structural dynamics, external excitation High-frequency fluctuation Random process or envelope model

I note that not all uncertainties are easy to quantify. In practical reliability analysis of an industrial robot, I usually select the error terms that have the largest influence on the end-effector pose. The geometric errors are often modeled as normal random variables because their standard deviations are much smaller than their means. The ratio of standard deviation to mean is often on the order of one thousandth. Under this assumption, the position and orientation error components are also approximately normal, which simplifies the reliability calculation.

Point Reliability Model

I formulate point reliability for an industrial robot by defining a tolerance region around the desired pose. The end effector is considered reliable if the actual pose error vector lies inside this region. A common choice is a spherical tolerance region for combined position and orientation error. Let the position error components be $x$, $y$, and $z$, and let the orientation error components be $\alpha$, $\beta$, and $\gamma$. I define the comprehensive error as:

$$ p = \sqrt{x^2 + y^2 + z^2 + \alpha^2 + \beta^2 + \gamma^2} $$

The point reliability is the probability that the comprehensive error is less than the allowable threshold $r$:

$$ R = \Pr\{ x^2 + y^2 + z^2 + \alpha^2 + \beta^2 + \gamma^2 \le r^2 \} $$

The corresponding failure probability is:

$$ p_f = \Pr\{ x^2 + y^2 + z^2 + \alpha^2 + \beta^2 + \gamma^2 \ge r^2 \} $$

When the comprehensive error equals the tolerance radius, the industrial robot is in a limit state. If the error reaches or exceeds this critical value, I consider the system to have failed. This model is simple and useful for point welding, drilling, and rapid positioning, but it does not account for the risk accumulated between discrete points. I therefore treat point reliability as a local measure, not a global measure of task performance.

To compute point reliability, I need the probability distribution of the error vector. If the error components are independent normal variables with zero mean and known variances, the squared comprehensive error follows a chi-square distribution. If the components are correlated, I use the covariance matrix and a quadratic form. In many industrial robot applications, the orientation errors are converted to equivalent linear errors at the tool center point, which allows a unified position-error model. I often use a first-order approximation because the nonlinearity of the kinematic model is weak within the small tolerance zone.

Time-Varying Reliability Model

I now consider the continuous motion of an industrial robot. The end effector follows a trajectory from an initial time $t_0$ to a final time $t_e$. The trajectory is reliable only if every point on the trajectory remains within the allowable error band. This requirement is stricter than point reliability because a single excursion outside the band causes failure of the whole task. I define the time-varying reliability as:

$$ R(t_0,t_e) = \Pr\left\{ \bigcap_{j=1}^{6} |g_j(\mathbf{X}, \theta)| \le \varepsilon, \forall t \in [t_0,t_e] \right\} $$

Here, $g_j(\mathbf{X}, \theta)$ represents the motion error function for each position or orientation component, $\mathbf{X}$ is the vector of uncertain parameters, $\theta$ is the joint variable vector, and $\varepsilon$ is the allowable error. The symbol $\bigcap$ indicates that all constraints must be satisfied simultaneously over the entire interval. I can also express the failure probability as the probability that at least one constraint is violated:

$$ p_f(t_0,t_e) = \Pr\left\{ \bigcup_{j=1}^{6} \left( \max_{t \in [t_0,t_e]} |g_j(\mathbf{X}, \theta)| \gt \varepsilon \right) \right\} $$

This formulation is equivalent to an extreme-value problem. The reliability depends on the maximum deviation over time, not on the average deviation. For an industrial robot performing a continuous task, the maximum deviation is often caused by a combination of geometric error, joint clearance, and dynamic vibration. The time-varying model therefore captures the cumulative effect of uncertainties along the trajectory.

I illustrate the idea with a trajectory in three-dimensional space. The desired path is a smooth curve, and the actual path fluctuates around it. If the fluctuation stays inside the tolerance tube, the motion is reliable. If the actual path touches or crosses the boundary of the tolerance tube at any time, the motion fails. This geometric interpretation is useful because it converts the dynamic reliability problem into a boundary-crossing problem. The tolerance tube can be defined in position space, orientation space, or a combined six-dimensional space.

Model aspect Point reliability Time-varying reliability
Constraint domain Single pose or discrete poses Continuous time interval
Failure event Error exceeds threshold at one point Error exceeds threshold at any time
Mathematical nature Static probability Extreme-value or first-passage probability
Typical method Monte Carlo, first-order second-moment, moment method Envelope method, first-passage method, surrogate model
Industrial robot application Drilling, spot welding, pick-and-place Arc welding, spraying, medical robotics

Solution Methods for Motion Reliability

I compare four main solution methods for the motion reliability of an industrial robot: Monte Carlo simulation, the first-order second-moment method, the envelope method, and the first-passage method. Each method has a different balance between accuracy, efficiency, and applicability. I use these methods to evaluate either point reliability or time-varying reliability depending on the problem formulation.

Monte Carlo Simulation

Monte Carlo simulation is a numerical method based on random sampling. I construct a probabilistic model of the industrial robot motion, generate many random samples of the uncertain parameters, and evaluate the motion error for each sample. The reliability is estimated as the fraction of samples that satisfy the tolerance constraint. The core idea is that the sample average converges to the true probability as the number of samples increases. The law of large numbers guarantees convergence under mild conditions.

$$ \hat{R} = \frac{1}{N} \sum_{i=1}^{N} I\{ g(\mathbf{X}_i) \le 0 \} $$

Here, $N$ is the number of samples, $\mathbf{X}_i$ is the $i$-th random sample, $g(\mathbf{X})$ is the limit state function, and $I\{\cdot\}$ is the indicator function. The estimated failure probability is:

$$ \hat{p}_f = \frac{N_f}{N} $$

Monte Carlo simulation is accurate and general. It can handle nonlinear kinematic models, non-normal distributions, and complex tolerance regions. However, it requires a large number of samples when the failure probability is small. For an industrial robot with high reliability, the failure probability may be on the order of $10^{-4}$ or lower, which means that millions of samples may be needed for a stable estimate. This computational cost is the main disadvantage of the method.

First-Order Second-Moment Method

The first-order second-moment method is an approximate reliability method. I use the first two moments of the random variables, namely the mean and the variance, to estimate the reliability index and the failure probability. I linearize the limit state function around the most probable failure point. If the limit state function is $g(\mathbf{X})$, the reliability index is:

$$ \beta = \frac{\mu_g}{\sigma_g} $$

where $\mu_g$ is the mean of the limit state function and $\sigma_g$ is its standard deviation. Under the assumption that $g(\mathbf{X})$ is normal, the reliability is:

$$ R = \Phi(\beta) $$

and the failure probability is:

$$ p_f = 1 – \Phi(\beta) = \Phi(-\beta) $$

Here, $\Phi(\cdot)$ is the standard normal cumulative distribution function. The first-order second-moment method is efficient and easy to implement. I use it when the nonlinearity of the industrial robot kinematic model is moderate and the random variables are approximately normal. Its accuracy decreases when the limit state function is highly nonlinear or when the input distributions are far from normal. In such cases, I may use a second-order method or a moment-based method with higher-order moments.

Envelope Method

The envelope method converts the time-varying reliability problem of an industrial robot into a static geometric problem. I construct an envelope that bounds the possible motion error over the entire time interval. The envelope can be a spatial boundary, a tube around the nominal trajectory, or a set of extreme values of the error function. The reliability is then computed from the probability that the envelope remains inside the tolerance region.

$$ E(t) = \{ \mathbf{e}(t) : \mathbf{e}(t) = \mathbf{X}(t) – \mathbf{X}_d(t) \} $$

$$ R = \Pr\left\{ \max_{t \in [t_0,t_e]} \| \mathbf{e}(t) \| \le \varepsilon \right\} $$

The envelope method is computationally efficient because it avoids sampling the full trajectory at every time step. It is particularly useful for industrial robot tasks with smooth trajectories and moderate uncertainty. The main limitation is that the envelope may be conservative. If the envelope is too wide, the estimated reliability is lower than the true reliability. If the envelope is too narrow, the method may overestimate reliability. I therefore require a careful construction of the envelope based on the kinematic and dynamic characteristics of the industrial robot.

First-Passage Method

The first-passage method is a classical approach for time-varying reliability. I treat the motion error as a random process and compute the probability that the process crosses the failure threshold for the first time within the interval. If the crossing events are rare and approximately independent, the failure probability can be approximated by an exponential function of the expected number of crossings.

$$ P_f(t_0,t_e) \approx 1 – \exp\left( -\int_{t_0}^{t_e} \nu^+(t) \, dt \right) $$

Here, $\nu^+(t)$ is the up-crossing rate of the random process. The up-crossing rate is defined as:

$$ \nu^+(t) = \lim_{\Delta t \to 0} \frac{\Pr\{ g(t) \le 0 \cap g(t+\Delta t) \gt 0 \}}{\Delta t} $$

For a stationary Gaussian process, the up-crossing rate has a closed-form expression involving the spectral moments. For a non-stationary process, I use time-dependent spectral moments or numerical integration. The first-passage method is well suited to the continuous motion of an industrial robot because it directly models the dynamic failure event. Its accuracy depends on the Poisson assumption for crossings. When crossings cluster or when the process is narrow-band, the method may need correction.

Method Core idea Advantages Limitations Best use for industrial robot
Monte Carlo Random sampling and statistical estimation High accuracy, general, easy to implement High computational cost for low failure probability Validation of other methods, complex nonlinear models
First-order second-moment Linearization and first two moments Efficient, simple, widely used Less accurate for strong nonlinearity and non-normal variables Point reliability with moderate uncertainty
Envelope Dynamic problem converted to static geometric boundary Efficient, intuitive, good for smooth trajectories Conservatism depends on envelope construction Time-varying reliability of continuous paths
First-passage Crossing rate of a random process Directly models dynamic failure, suitable for time-varying reliability Requires Poisson or narrow-band assumptions Continuous tasks with random vibration and wear

Uncertainty Propagation in an Industrial Robot

I now examine how uncertainty propagates from the joint space to the task space of an industrial robot. The kinematic model is nonlinear, but the error model is often linearized because the deviations are small. The linearized model is convenient for reliability analysis, but I must check its validity when the joint clearance is large or when the industrial robot operates near a singular configuration. Near a singularity, the Jacobian becomes ill-conditioned, and small joint errors can produce large end-effector errors. This effect can dominate the motion reliability.

I represent the uncertain parameters as a vector $\mathbf{X}$. The components may include link lengths, link twists, joint offsets, joint angles, gear ratios, and clearance parameters. In a probabilistic framework, I assign a probability density function to each component. The joint probability density function is denoted by $f_{\mathbf{X}}(\mathbf{x})$. The failure probability is then an integral over the failure domain:

$$ p_f = \int_{\Omega_f} f_{\mathbf{X}}(\mathbf{x}) \, d\mathbf{x} $$

where $\Omega_f$ is the region of parameter space for which the motion error exceeds the tolerance. For point reliability, $\Omega_f$ is defined at a single pose. For time-varying reliability, $\Omega_f$ is defined by the maximum error over the interval. In most cases, the integral cannot be evaluated analytically, so I use numerical or approximate methods.

Parameter Symbol Distribution assumption Effect on industrial robot pose
Link length $a_i$ Normal or truncated normal Position error along link direction
Link twist $\alpha_i$ Normal Orientation error and coupled position error
Joint offset $d_i$ Normal Position error along joint axis
Joint angle $\theta_i$ Normal or uniform Pose error through Jacobian
Joint clearance $c_i$ Uniform or truncated normal Nonlinear and impact-related error
Gear backlash $b_i$ Uniform or normal Periodic joint error
Link compliance $k_i$ Lognormal or normal Load-dependent deflection

I often use a sensitivity analysis to rank the contribution of each parameter to the motion reliability of an industrial robot. The sensitivity coefficient can be defined as the partial derivative of the reliability index with respect to the mean or standard deviation of a parameter. Parameters with large sensitivity coefficients are the main targets for tolerance design, calibration, and condition monitoring. This ranking helps engineers allocate manufacturing precision and maintenance resources efficiently.

Reliability-Based Design and Optimization

I can use motion reliability as an objective or constraint in the design of an industrial robot. Reliability-based design optimization seeks to minimize cost or maximize performance while ensuring that the reliability exceeds a target value. For an industrial robot, the design variables may include link dimensions, joint stiffness, gear precision, and controller parameters. The uncertain variables include manufacturing tolerances, payload variation, and environmental conditions.

$$ \min_{\mathbf{d}} \quad C(\mathbf{d}) $$

$$ \text{subject to} \quad R(\mathbf{d}, \mathbf{X}) \ge R_{\text{target}} $$

Here, $\mathbf{d}$ is the vector of design variables, $C(\mathbf{d})$ is the cost function, and $R_{\text{target}}$ is the required reliability. The optimization is challenging because the reliability evaluation is computationally expensive. I often use surrogate models to approximate the limit state function or the reliability index. A surrogate model can be trained from a small number of high-fidelity simulations and then used for many optimization iterations.

For time-varying reliability, the optimization must consider the entire trajectory. I can parameterize the trajectory and treat the trajectory parameters as design variables. The objective is to maximize the minimum reliability along the path or to minimize the probability that the end effector leaves the tolerance tube. This approach is useful for industrial robot path planning in welding, spraying, and additive manufacturing.

Summary of Main Equations

Concept Equation Meaning
Forward kinematics $$ T_n^0 = \prod_{i=1}^{n} T_i^{i-1} $$ Pose of the end effector from base to tool
Linearized error $$ \Delta \mathbf{X} = \mathbf{J}_q \Delta \mathbf{q} + \mathbf{J}_p \Delta \mathbf{p} $$ Propagation of joint and link errors
Comprehensive error $$ p = \sqrt{x^2 + y^2 + z^2 + \alpha^2 + \beta^2 + \gamma^2} $$ Combined position and orientation error
Point reliability $$ R = \Pr\{ x^2 + y^2 + z^2 + \alpha^2 + \beta^2 + \gamma^2 \le r^2 \} $$ Probability of staying inside a tolerance sphere
Time-varying reliability $$ R(t_0,t_e) = \Pr\left\{ \bigcap_{j=1}^{6} |g_j(\mathbf{X}, \theta)| \le \varepsilon, \forall t \in [t_0,t_e] \right\} $$ Probability that all constraints hold over time
Monte Carlo estimate $$ \hat{R} = \frac{1}{N} \sum_{i=1}^{N} I\{ g(\mathbf{X}_i) \le 0 \} $$ Sampling estimate of reliability
Reliability index $$ \beta = \frac{\mu_g}{\sigma_g} $$ First-order second-moment safety measure
First-passage failure $$ P_f(t_0,t_e) \approx 1 – \exp\left( -\int_{t_0}^{t_e} \nu^+(t) \, dt \right) $$ Approximate time-varying failure probability

Future Research Directions

I see several promising directions for the motion reliability of industrial robots. The first direction is the fusion of multiple methods. Monte Carlo simulation is accurate but expensive, while analytical methods are fast but approximate. I can combine them by using a surrogate model trained on a small number of Monte Carlo samples. Machine learning models, such as Gaussian process regression and neural networks, can approximate the limit state function and reduce the computational cost of reliability analysis. This fusion is especially valuable when the industrial robot model is high-dimensional and nonlinear.

The second direction is dynamic and intelligent evaluation. The reliability of an industrial robot changes with wear, temperature, payload, and task history. I can integrate digital twin technology with online sensor data to update the reliability estimate in real time. A digital twin of an industrial robot can simulate the current state and predict the remaining useful life. Online sensors can measure joint torque, vibration, and temperature, and these measurements can be used to update the probability distributions of uncertain parameters. The result is an adaptive reliability assessment that supports predictive maintenance and adaptive compensation.

The third direction is the reliability analysis of multi-robot systems. Many industrial robot applications now use two or more robots working together. The motion reliability of a multi-robot system depends not only on the reliability of each industrial robot but also on the coordination and synchronization between them. The failure of one industrial robot can affect the entire task. I need new models that account for spatial constraints, communication delays, and shared workspace collisions.

The fourth direction is reliability under extreme and rare events. In some industrial robot tasks, the failure probability is extremely low, but the consequences are severe. Examples include medical robotics and hazardous material handling. Standard Monte Carlo simulation is inefficient for such rare events. I can use importance sampling, subset simulation, and other variance reduction techniques to estimate small failure probabilities efficiently. These methods are well developed in structural reliability and can be adapted to industrial robot motion reliability.

Future direction Key idea Expected benefit for industrial robot Main challenge
Multi-method fusion Combine surrogate models with sampling or analytical methods Lower computational cost with high accuracy Model training and validation
Dynamic and intelligent evaluation Digital twin and online sensing for real-time reliability Predictive maintenance and adaptive compensation Data quality, sensor placement, model updating
Multi-robot reliability Model coordination, synchronization, and shared workspace Reliable cooperative tasks High-dimensional coupling and collision risk
Rare-event reliability Importance sampling and subset simulation Efficient estimation of very small failure probabilities Design of efficient sampling densities
Reliability-based path planning Optimize trajectory with reliability constraints Guaranteed precision along the whole path Computational cost of time-varying constraints

Discussion

I believe that the motion reliability of an industrial robot should be evaluated with a clear understanding of the task requirements. Point reliability is sufficient for tasks that are defined by discrete target poses. Time-varying reliability is necessary for tasks that require continuous path accuracy. The choice of method should consider the required accuracy, the available computational resources, and the nature of the uncertain parameters. Monte Carlo simulation remains the reference method for validation. The first-order second-moment method is useful for quick estimates. The envelope method is efficient for smooth trajectories. The first-passage method is powerful for dynamic failure analysis.

I also emphasize that reliability is not only a mathematical property but also an engineering property. It depends on manufacturing quality, assembly precision, calibration, maintenance, and operating conditions. A high-reliability industrial robot must be designed with tolerances that are consistent with the required task accuracy. It must be calibrated after assembly and periodically during service. It must be monitored to detect wear and degradation. The reliability model is a tool that connects these engineering decisions to quantitative performance measures.

In my view, the most important challenge is the integration of kinematic error, dynamic error, and control error into a unified reliability framework. The kinematic error model captures geometric deviations. The dynamic model captures vibration, flexibility, and inertia effects. The control model captures tracking error and delay. A complete reliability model for an industrial robot should include all three sources. This integration is difficult because the models have different time scales and different mathematical structures. However, it is necessary for high-speed and high-precision applications.

Another challenge is the treatment of epistemic uncertainty. Some parameters are random in a frequentist sense, while others are uncertain because of limited knowledge. For example, the wear rate of a joint may be known only within a range. I can use evidence theory, interval analysis, or fuzzy set theory to represent this type of uncertainty. A combined probabilistic and epistemic model can provide a more realistic reliability estimate. The result may be an interval or a belief measure rather than a single probability. This approach is useful when data are scarce or when the industrial robot operates in a new environment.

Conclusion

I have reviewed the motion reliability of industrial robots from the perspectives of point reliability and time-varying reliability. I constructed kinematic and error models, formulated reliability models, and compared Monte Carlo simulation, the first-order second-moment method, the envelope method, and the first-passage method. I also summarized the main equations, uncertainty sources, and future research directions. The reliability of an industrial robot is a key factor in precise manufacturing, and it must be evaluated over the entire task cycle when continuous accuracy is required.

My conclusion is that no single method is universally optimal. The best approach depends on the task, the tolerance, the uncertainty level, and the available computational budget. I recommend a hybrid strategy that uses analytical or surrogate methods for rapid evaluation and Monte Carlo simulation for validation. I also recommend the use of digital twin and online sensing for dynamic reliability assessment. With these advances, the motion reliability of an industrial robot can be predicted, maintained, and improved throughout its service life.

Scroll to Top